x

Land Pride RCM5014

Land Pride RCM5014 for sale at Evergreen Tractor, Louisiana

Double tap to zoom

Land Pride RCM5014 for sale at Evergreen Tractor, Louisiana

 

Features

Features Benefits
Surpassed rugged
industry standards
All Land Pride Cutters have been designed and tested and meet rigorous voluntary
testing procedures specified by ANSI.
Factory assembled Saves customer set-up time and money.
Fully welded deck Fully welded deck adds strength.
250 HP Divider gearbox
210 HP center & wing gearboxes
A rugged heavy built gearboxes capable of handling heavy cutting applications.
Gearbox seal protection Gearbox bottom seal protection for longer bearing life.
Input driveline:
Cat. 6 CV
Holds up to shock loads and harsh mowing conditions. Fits wide range of tractors including high horsepower tractors.
Star profile drivelines Star profile spreads load out to many points on the shaft. More apt to resist bending and
twisting under shock loads and harsh mowing conditions.
Easy greasable drivelines Drivelines have access holes for greasing the U-joints and to grease the inner profiles.
4 Plate slip-clutch Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline
when impacts are encountered.
High blade tip speed

540 rpm: Center: 17,377 fpm (88.3 mps), Wings: 17,329 fpm (88 mps)
1000 rpm: Center: 18,165 fpm (92.3 mps), Wings: 18,317 fpm (93.1 mps)

Allows for a clean cut of material and even distribution.
6" Blade overlap Generous blade overlap eliminates skipping, especially in turns.
High cutting capacity Can cut brushy areas with saplings up to 3".
10 1/2" Deck height Handles heavy cutting, which reduces balling-up of cut material under the deck.
3/16" Stump jumper backed
with a 1" thick mounting bar
Heavy round stump jumper with bottom gearbox seal protector. Can hold up to tough
conditions.
3/16" Deck thickness Heavy enough to handle conditions but not weigh unit down.
Self-leveling pull-type hitch Reduces drawbar wear by keeping hitch level while going through ditches.
LED Signal lights LED lights are bright, long lasting, and resistant to vibration, unlike incandescent counterparts.
Hinged wing section Allow cutter to follow terrain. Ideal for rough ground where hillsides, ditches and hollows
can cause uneven cutting.
1" Solid hinge rods Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in
the hinge area itself.
Wing transport lock Safety feature. Holds wing section up in case of hydraulic pressure loss.
Enclosed front to rear dual leveling
rods
Dual leveling rods enable the cutter to pull equally on the rear axle during travel over
rough terrain. Many competitors only use one leveling rod.
Drain holes in wheel rims Allows water to drain from wheels mounted on the folded-up wing.
Helps prevent paint deterioration and rusting to the wheel rims.
5" Square rear axle tubing Heavy axle to handle harsh conditions.
Spring-cushioned center-axle Protects unit from bumps and ground shock.
Replaceable wheel spindles Wheel spindles can be replaced when damaged without replacing the entire axle.
Simply remove two bolts to replace damaged spindle.
Double swivel hitch Great for uneven terrain, reduces drawbar wear.
Bar-tite hitch (optional) Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.
Wheel options Laminated tires: Eliminates flats.
Airplane tires without foam filling: Give better cushion while transporting.
Airplane tires with foam filling: Give better cushion while transporting & can’t go flat.
Deck rings (optional) 1/2" x 3" full welded deck ring keeps blades from damaging the deck.

 

 

Specifications

Specifications & Capacities RC5014 & RCM5014
Min. horsepower 90 power take-off horsepower (67.1 kw)
Gearbox horsepower 250 (186.4 kw) Splitter
225 (167.8 kw) Center deck & wing deck
Gearbox
lubrication & capacity
Center deck & wing: 10 pints (4.73 L) of gear lube 80-90W EP
Divider gearbox: 5.5 pints (2.60 L) of gear lube 80-90W EP
Cutting capacity Up to 3" (7.6 cm) material
Machine weight 7,340 lbs. (3,329.4 kg)
Blade tip speed
At 540 rpm
At 1000 rpm

Center blade: 17,377 FPM (88.3 mps) & wing blade: 17,329 FPM (88 mps)
Center blade: 18,165 FPM (92.3 mps) & wing blade: 18,317 FPM (93.1 mps)
Tongue weight 2,668 lbs. (1,210.2 kg)
Hitch types Standard clevis hitch, pintle hitch, ball hitch, LP performance hitch and bar-tite hitch
Hitch jack Standard hand crank
Signal lights
7 Pin connector
LED (standard)
SAE J560 pin configuration
Cutting width SAE J560 pin configuration
Cutting width
Overall width
Minimum transport width
13'-6" (4.11 m)
15' (4.57 m)
8'-9" (2.44 m)
Overall length 19'-3" (5.87 m)
Deck height 10 1/2" (3.06 m)
Cutting height* 2" (5.1 cm) to 14" (35.6 cm) with hydraulic cylinder and stroke control spacers
Lift hydraulics 4" x 8" Hydraulic cylinder, hoses, fittings & stroke control spacers
Wing hydraulics 3 1/2" x 12" Hydraulic cylinders, hoses & fittings
Wing transport protection Wing transport lock
Deck sheet thickness 10g (3.4 mm) top and 10g (3.4 mm) bottom
Side skirt thickness 1/4" (6 mm)
Wing deck skid shoes
Center deck skid shoes
Weight box skid shoe
Replaceable
Replaceable
Replaceable
Blades - 4 (2 per carrier) 1/2" (13 mm) x 4" (10.2 cm) Heat-treated, free-swinging alloy steel with uplift
Blade overlap 6" (16.2 cm)
Blade bolt Keyed with hardened flat washer & locknut
Stump jumper
Blade holder
3/16" (5 mm) Round dish shaped bolt-on stump-jumper (optional)
1" (2.5 cm) diamond shaped blade bar
Deck rings (optional) 1/2" (13 mm) x 3" (7.6 cm) fully welded
Front & rear guards Single chain or double chain
Heavy duty Input driveline options Constant velocity u-joint ASAE Cat. 6 with or without over running clutch
Heavy duty Intermediate & wing drivelines ASAE Cat. 5 with slip-clutch protection
Tire & wheel options 6" x 21" Laminated tires
6" x 26" Laminated tires
27" x 7.75" x 15" Used aircraft tires with foam filling
29" Used aircraft tires
Number of wheel 5 - Wheel option: 4 on transport axle and one on wing axle
6- Wheel option: 4 on transport axle and two on wing axle
Transport axle Spring-cushioned on center transport axle or optional walking tandem on center axle
Hubs Cast iron 5-bolt hubs with tapered roller bearings and with 1 3/4" (4.4 cm) shafts